The WeMos D1 mini and its sensor and actuator shields

Introduction

We have seen that the ESP01 can be programmed with micro Python and that there are add-on sensor boards available. However, when we connect the sensor board we loose the serial connection to the PC. This can be corrected by soldering extra connectors to the top of the ESP01 board but this is fiddly and needs good soldering equipment and good soldering skills. The other option is to get access to the ESP01 through WiFi using WebRepl

A better and only slightly more expensive solution (we are talking about ~ 3.5 US$ instead of 2.5 US$) is the Wemos D1 mini board. This boards gives up more I/O connections and many more sensor and actuator shields are readily available on the market.

The processor board

ESP8266

The processor board uses an Espressif ESP8266 processor chip and 4 MBytes of flash are installed on the board.

wemosd1mini.png

You will find a description of the pinout at https://www.likecircuit.com/wemos-d1-mini-pinout

For convenience I copied the basic information here.

d1MiniPinout.png

In contrast to a PC the WeMos D1 mini has only very limited memory resources. While 4 MBytes of flash memory is rather comfortable, the amount of RAM (80 K) is a very limiting factor. When running micro Python a mere 30 kBytes is left for your Python programs. There are essentially 2 ways to make most out of the small amount of RAM:

  • You can pre-compile your programs to byte code, which takes less space in RAM
  • You can code freeze driver libraries, which means you integrate their byte code into The micro Python image. This however means that you must compile your own version of micro Python and flash it into the WeMos D1 CPU.

ESP32

As an alternative you have a CPU board based on the more powerful ESP32:

wemosEsp32.png

As for the ESP8266 there is a Micropython port for the ESP32. The drivers are essentially the same, the pinout of the board however (GPIO numbers for the pins) is different. This means that for every driver we must only change the GPIO number. Since it is possible to find out from Micropython on which platform we run (sys.platform tells you if your CPU is a "esp8266" or a "esp32") we can check for the CPU type and adapt the pin numbering as a consequence.

Here is a comparison of the pin assignments for the 2 CPUs:

ESP8266

  RESET RST Tx GPIO 1  
  ADC0 A0 Rx GPIO 3  
SCK GPIO 16 D0 D1 GPIO 5 SCL
MISO GPIO 14 D5 D2 GPIO 4 SDA
MOSI GPIO 12 D6 D3 GPIO 0  
SS GPIO 13 D7 D4 GPIO 2  
  GPIO 15 D8 GND GND  
  3.3V 3V3 5V 5V  

ESP32

  RESET RST Tx    
ADC1 channel 0 GPIO 36 SVP Rx    
  GPIO 26 IO26 IO22 GPIO 22 SCL
SCK GPIO 18 IO18 IO21 GPIO 21 SDA
MISO GPIO 19 IO19 IO17 GPIO 17  
MOSI GPIO 23 IO23 IO16 GPIO 16  
SS GPIO 5 IO5 GND GND  
  3.3V 3V3 5V 5V  

Sensor Shields

A big number of sensor and actuator boards are available. You will find a complete list with their description at https://wiki.wemos.cc/products:d1_mini_shields

Here are the sensor shields and their test programs for the workshop:

Here is an overview table showing the devices and the
Module Connections Functionality
1 button shield D3: GPIO 0 on / off push button
WS2812B RGB shield D2: GPIO 4 addressable rgb LED

DS1307 RTC and data logger

D1: GPIO 5 I2C SCL
D2: GPIO 4 I2C SDA

D5: GPIO 14 SPI Clock
D6: GPIO 12 SPI MOSI
D7: GPIO 13 SPI MISO
D8: GPIO 15 SPI CS

Real Time Clock

SD card interface

Buzzer shield D5 (default GPIO 14
D6 GPIO 12
D7 GPIO 13
D8 GPIO 15
passive buzzer
BMP180 shield D1 GPIO 5 I2C SCL
D2 GPIO 4 I2C SDA
I2C barometric pressure sensor and
temperature sensor
DHT11 shield D4 GPIO 2 temperature and humidity sensor
OLED shield D1 GPIO 5 I2C SLC
D2 GPIO 4 I2C SDA
64x48 pixel display with SSD1036 I2C controller
DD18B20 shield D2 GPIO 4 1-wire digital temperature sensor
SHT30 shield D1 GPIO 5 I2C SCL
D2 GPIO 4 I2C SDA
I2C temperature and humidity sensor
LED Matrix shield D5 GPIO 14 CLK
D7 GPIO 13 Din
8x8 LED Matrix
ir connections:

For each of the devices I create 2 directories:

  • a driver directory containing programs testing the module without Cayenne communication
  • a cayenne directory for the final program

You can find the code written for the workshop on github: https://github.com/uraich/MicroPython_IoTDemos.

Comments

Topic attachments
I Attachment History Action Size DateSorted ascending Who Comment
PNGpng d1MiniPinout.png r1 manage 542.9 K 2019-03-20 - 09:27 UliRaich  
PNGpng wemosd1mini.png r1 manage 313.5 K 2019-03-20 - 09:20 UliRaich  
PNGpng wemosEsp32.png r1 manage 213.3 K 2019-05-07 - 17:49 UliRaich  
Edit | Attach | Watch | Print version | History: r13 | r9 < r8 < r7 < r6 | Backlinks | Raw View | Raw edit | More topic actions...
Topic revision: r7 - 2019-05-07 - UliRaich
 
  • Edit
  • Attach
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2024 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback