I2CEEProm < Embedded_Systems

Tags: view all tags
---+ Exercise 15: EEPROM and Driver Access
---++ Goal:

The goal of this exercise is twofold: First we will learn about an EEPROM, a Electrically Erasable Read Only Memory. These devices are often used in instruments to store calibration values or configuration parameters. EEPROMs can usually be read byte by byte but can be erased and written only in blocks.

The at24c32 EEPROM is mounted together with the DS1307 RTC on the Tiny RTC module (chip on the right). The Tiny RTC module therefore responds to 2 I2C addresses. You find these 2 addresses with the i2cdetect command and you can figure out from the data sheets which of the addresses corresponds to which chip.

The data sheet for the at24c32 can be found here:

http://www.atmel.com/Images/doc0336.pdf

<img alt="rtc.png" height="453" src="%ATTACHURL%/rtc.png" title="rtc.png" width="436" />

---++ Examination exercises

For the examination please solve exercise 1-3 of this exercise list. *%RED%Exercise 4 is not part of the examination!%ENDCOLOR%*

For all three exercises, write
   * the C code
   * a Makefile
   * a shell script that sets up the LD_LIBRARY_PATH to include /opt/ucc/lib, such that the at24c32 library can be found (not necessary of course if you do not use the at24c32 library)
   * a short description on how you designed the program and what the individual steps are that the program takes to solve the problem.
---++ Exercise 1: Read the EEPROM

The at24c32 is a 32 kBit device and can therefore store a total of 4096 bytes (4096 * 8 = 32 kBit). Like the DAC it is an I2C device. To make things easier for you, again a library is supplied.

The documentation of the library is again generated from the source code and can be found at the URL:

https://dcsit.twiki.ucc.edu.gh/html/libDoc/at24c32

This one is an exercise for detectives: There is a secret message hidden in the EEPROM and your job is to uncover the mystery. So… Sherlock Holmes and Dr. Watson: show your talents and find out the contents of the message. Write a program called <i>readEnigma </i>reading the EEPROM and printing its content in hex (%x) and as characters (%c).
---++ Exercise 2: Re-write the program without using the library

Since there are only very few library calls it is also possible to access the EEPROM through pigpio calls avoiding my library all together. Make sure you get the same result as in the first exercise.
---++ Exercise 3: Write the EEPROM

Prepare a buffer with some data to be written to the EEPROM. Use your previous program to read these data back. Power down the Raspberry Pi, wait a minute and then switch it back on again. Verify that you can still read back the data.

The pdf of the examination exercises are found here:

%ATTACHURL%/csc_exam.pdf

%RED% *It is possible to access the I2C driver directly and it was my intention to show you how to do this. Unfortunately we did not make it up a level where we can understand how a device driver works. The following exercises it there not part of the examination exercises!* %ENDCOLOR%
---++ Exercise 4: Write an access library

The full description on how to access I2C devices through the driver directly is found [[https://www.mjmwired.net/kernel/Documentation/i2c/dev-interface][here.]]

Separate out the open, close, read, write … functions into individual files. Rewrite your programs such that you call these generic functions, which can be re-used by other programs.

These are the functions that should be available:
   * <p>at24c32Open</p>
   * <p>at24c32Close</p>
   * <p>at24c32Read</p>
   * <p>at24c32Write</p>
   * <p>at24c32Debug (switching debugging information on or off)</p>
-- %USERSIG{UliRaich - 2017-08-21}%

---++ Comments

%COMMENT%
Attachments
Topic attachments
I	Attachment	History	Action	Size	Date	Who
pdf	csc_exam.pdf	r1	manage	1692.7 K	2017-11-29 - 16:03	UnknownUser
png	rtc.png	r1	manage	1118.1 K	2017-10-25 - 18:06	UnknownUser
odt	session_14.odt	r1	manage	1142.5 K	2017-11-21 - 16:49	UnknownUser
Topic revision: r6 - 2017-11-29 - uli