Motor Movement (Single Step Forward)

• pigpio

Types of functions in pigpio

• There are functions to
• Initialize the library and close it
• Control gpio lines and read from or write to them
• Get a call-back when a gpio state changes
• Access routines to the I2C bus
• Access routines to the SPI interface
• PWM functions
• Functions for use of a serial device

Features of pigpio

This is how to use the library

Initializing pigpio

A typical Makefile with pigpio

Reading command line arguments

Using getopt_long

Call getopt and interpret

Write the stepper program

• Select the movement mode
• Select the movement speed
• Select if you turn clockwise or counter clock wise
• Select how have to move of to which angle

-- Uli Raich - 2017-11-01

<--/commentPlugin-->

The 27BJY-48 stepper motor and its ULN-2803 driver module

A lecture on youtube

There is an excellent lecture describing the usage of exactly our stepper motor setup on youtube

Movement Double Phase Forward

Double Step Forward Table

Of course our signal table must change correspondingly,

our program to send out the signals for one full cycle stays the same however.

Programming double step forward mode

For this, nothing much is to be said:

We change the table, but since the program is independent

from the contents of the stepping table, the code stays strictly the same

Position of rotor in doubleStepForward mode

An important point to note is that the rotor moves half a step

further than in single Step Forward because its north pole

is now attracted by the top and the bottom south poles.

By first powering only the upper coil, then powering both coils

then powering again only one pole of the lower coil it should

be possible to move the motor by half steps only

and by doing so increase its resolution.

This is what we call half step mode and it is a combination

of single and double step forward modes.

The torque of the motor is less than in double step forward

and the speed is only about half because now we need 8 steps for a full cycle.

Movement Half Step Forward

Half Step Forward Table

Programming Half Step Mode

Again, apart from the fact that we must now pass through

a table of 8 entries instead of 4 the program does not change.

If we use the signature of all bits being zero

as end of table indicator then no change at all is required.

The pigpio library

Up to now we always used wiringPi to access our GPIO pins.

I explained in the first lecture on the Raspberry Pi

that there are 2 independent libraries available:

• wiringPi
• wigpio

Advantages of pigpio

The pigpio library comes in 2 versions:

• The standard one where calls to the library code
  results in direct access to the hardware
• The daemon version where first a daemon (pigpiod)
  is started and then the hardware access is only made in this daemon

Accessing the daemon

The daamon is started once before we make any hardware access:

sudo pigpiod

After this all hardware access can be make by a normal user

The program communicates with the deamon through library calls

which connect to the daemon through

• pipes (when running on the Raspberry Pi) or
  
  
• through sockets when running on a remote system
  like our Ubuntu PC

We can write C programs on the PC with hardware access

to our devices on the bread board through pigpio calls to the

PC version of the library which communicates

with the pigpio daemon on the Raspberry Pi

Documentation of pigpio

Slide 1: Stepping Motors

Lecture 9

Uli Raich

UCC semester 2017/2018

Slide 2: The 27BJY-48 stepper motor and its ULN-2803 driver module

Slide 3: Stepping Motors versus DC Motors

While DC motors simply spin when they are powered,

stepping motors can be moved in defined steps and thus positioned very precisely.

They contain 2 coils which can be powered in positive or negative

direction making the current flow in normal or reverse direction

and thus creating magnetic fields of opposite polarity

The rotor has a series of magnets (16 in case of the 28BYJ-48 which we are using)

with alternating opposite polarization.

A north pole followed by a south pole followed by a north pole and so on.

The motor base has 2*16 teeth which can be polarized as

north or south poles depending on the direction of the coil current.

Here is the data sheet of the 28BYJ-48

Slide 4: The Driver Card

The maximum current that a GPIO pin on the Raspberry Pi can deliver is 60 mA

which is insufficient to power the motor coils.

We therefore need a driver circuit (Darlington stage) to amplify

this current. In our case we use the ULN-2803 chip

The little PCB has 4 LEDs on it to show which of the 2 coils is

powered and in which direction. This is very useful to demonstrate which signals

are sent to the motor and it illustrates nicely the functioning of the motor.

Slide 5: Connecting the Driver to the Motor

We can see from the connections that when powering the pink line

the coil current is flowing in one direction while when

powering the orange line it is flowing in the opposite direction

Slide 6: Motor Movement

First we power the first coil in such a way the the first tooth has a

south pole and the second one a north pole, which

makes the rotor (whose north magnet is considered) moves to the first tooth.

Then we switch off the first coil and power the second coil such that

the first tooth of the lower row has a south pole.

This makes the rotor move to this tooth.

Now switch off the second coil and switch the first one on again,

however this time with reverse current. The second tooth of the

upper row now has the south pole

(the poles are inversed with respect to the first step).

Now we switch on only the second coil with inverse current to make

the rotor move to the forth tooth. From now on the whole cycle repeats.

Signal Table for Single Phase Forward

We have seen in the last slide how we have to power the coils to

make the stepping motor move by 1 cycle, which is 4 steps in case of

Single Phase Forward stepping

How does this translate into a program?

We connect the 4 phases (coil 1 forward, coil 2 backward, coil 1 backward, coil 2 forward)

to 4 GPIO pins on the Raspberry Pi cobbler

Then we create the following signal table, which is a 2-dimensional array of booleans:

Sending the pulses to the hardware

Now all we have to do is to go through this table and, for each step,

send a high level to the GPIO pin to which we connected the coils.

Going through one step cycle

Other modes of operation

Single Step forward (and backward) works fine but we can do better.

Up to now we have always powered only one coil at a time.

It is however possible to power both coils at the same time.

This will draw of course more current but the motor will get

a higher torque and can therefore handle bigger loads.

Movement Double Phase Forward

Double Step Forward Table

Of course our signal table must change correspondingly,

our program to send out the signals for one full cycle stays the same however.

Programming double step forward mode

For this, nothing much is to be said:

We change the table, but since the program is independent

from the contents of the stepping table, the code stays strictly the same

Movement Half Step Forward

Half Step Forward Table

Programming Half Step Mode

Again, apart from the fact that we must now pass through

a table of 8 entries instead of 4 the program does not change.

If we use the signature of all bits being zero

as end of table indicator then no change at all is required.

The pigpio library

Up to now we always used wiringPi to access our GPIO pins.

I explained in the first lecture on the Raspberry Pi

that there are 2 independent libraries available:

• wiringPi
• wigpio

Advantages of pigpio

The pigpio library comes in 2 versions:

• The standard one where calls to the library code
  results in direct access to the hardware
• The daemon version where first a daemon (pigpiod)
  is started and then the hardware access is only made in this daemon

Accessing the daemon

The daamon is started once before we make any hardware access:

sudo pigpiod

After this all hardware access can be make by a normal user

The program communicates with the deamon through library calls

which connect to the daemon through

• pipes (when running on the Raspberry Pi) or
  
  
• through sockets when running on a remote system
  like our Ubuntu PC

We can write C programs on the PC with hardware access

to our devices on the bread board through pigpio calls to the

PC version of the library which communicates

with the pigpio daemon on the Raspberry Pi

Documentation of pigpio

%SLIDESHOWSTART%

Stepping Motors

Lecture 9

Uli Raich

UCC semester 2017/2018

The 27BJY-48 stepper motor and its ULN-2803 driver module

Stepping Motors versus DC Motors

While DC motors simply spin when they are powered,

stepping motors can be moved in defined steps and thus positioned very precisely.

They contain 2 coils which can be powered in positive or negative

direction making the current flow in normal or reverse direction

and thus creating magnetic fields of opposite polarity

The rotor has a series of magnets (16 in case of the 28BYJ-48 which we are using)

with alternating opposite polarization.

A north pole followed by a south pole followed by a north pole and so on.

The motor base has 2*16 teeth which can be polarized as

north or south poles depending on the direction of the coil current.

Here is the data sheet of the 28BYJ-48

The Driver Card

The maximum current that a GPIO pin on the Raspberry Pi can deliver is 60 mA

which is insufficient to power the motor coils.

We therefore need a driver circuit (Darlington stage) to amplify

this current. In our case we use the ULN-2803 chip

The little PCB has 4 LEDs on it to show which of the 2 coils is

powered and in which direction. This is very useful to demonstrate which signals

are sent to the motor and it illustrates nicely the functioning of the motor.

Connecting the Driver to the Motor

We can see from the connections that when powering the pink line

the coil current is flowing in one direction while when

powering the orange line it is flowing in the opposite direction

Motor Movement

First we power the first coil in such a way the the first tooth has a

south pole and the second one a north pole, which

makes the rotor (whose north magnet is considered) moves to the first tooth.

Then we switch off the first coil and power the second coil such that

the first tooth of the lower row has a south pole.

This makes the rotor move to this tooth.

Now switch off the second coil and switch the first one on again,

however this time with reverse current. The second tooth of the

upper row now has the south pole

(the poles are inversed with respect to the first step).

Now we switch on only the second coil with inverse current to make

the rotor move to the forth tooth. From now on the whole cycle repeats.

Signal Table for Single Phase Forward

We have seen in the last slide how we have to power the coils to

make the stepping motor move by 1 cycle, which is 4 steps in case of

Single Phase Forward stepping

How does this translate into a program?

We connect the 4 phases (coil 1 forward, coil 2 backward, coil 1 backward, coil 2 forward)

to 4 GPIO pins on the Raspberry Pi cobbler

Then we create the following signal table, which is a 2-dimensional array of booleans:

Sending the pulses to the hardware

Now all we have to do is to go through this table and, for each step,

send a high level to the GPIO pin to which we connected the coils.

Going through one step cycle

Other modes of operation

Single Step forward (and backward) works fine but we can do better.

Up to now we have always powered only one coil at a time.

It is however possible to power both coils at the same time.

This will draw of course more current but the motor will get

a higher torque and can therefore handle bigger loads.

Movement Double Phase Forward

Double Step Forward Table

Of course our signal table must change correspondingly,

our program to send out the signals for one full cycle stays the same however.

Programming double step forward mode

For this, nothing much is to be said:

We change the table, but since the program is independent

from the contents of the stepping table, the code stays strictly the same

Position of rotor in doubleStepForward mode

An important point to note is that the rotor moves half a step

further than in single Step Forward because its north pole

is now attracted by the top and the bottom south poles.

By first powering only the upper coil, then powering both coils

then powering again only one pole of the lower coil it should

be possible to move the motor by half steps only

and by doing so increase its resolution.

This is what we call half step mode and it is a combination

of single and double step forward modes.

The torque of the motor is less than in double step forward

and the speed is only about half because now we need 8 steps for a full cycle.

Movement Half Step Forward

Half Step Forward Table

Programming Half Step Mode

Again, apart from the fact that we must now pass through

a table of 8 entries instead of 4 the program does not change.

If we use the signature of all bits being zero

as end of table indicator then no change at all is required.

The pigpio library

Up to now we always used wiringPi to access our GPIO pins.

I explained in the first lecture on the Raspberry Pi

that there are 2 independent libraries available:

• wiringPi
• wigpio

Advantages of pigpio

The pigpio library comes in 2 versions:

• The standard one where calls to the library code
  results in direct access to the hardware
• The daemon version where first a daemon (pigpiod)
  is started and then the hardware access is only made in this daemon

Accessing the daemon

The daamon is started once before we make any hardware access:

sudo pigpiod

After this all hardware access can be make by a normal user

The program communicates with the deamon through library calls

which connect to the daemon through

• pipes (when running on the Raspberry Pi) or
  
  
• through sockets when running on a remote system
  like our Ubuntu PC

We can write C programs on the PC with hardware access

to our devices on the bread board through pigpio calls to the

PC version of the library which communicates

with the pigpio daemon on the Raspberry Pi

Documentation of pigpio

%SLIDESHOWEND%

--

Slide 1: Stepping Motors

Lecture 9

Uli Raich

UCC semester 2017/2018

Slide 2: The 27BJY-48 stepper motor and its ULN-2803 driver module

Slide 3: Stepping Motors versus DC Motors

While DC motors simply spin when they are powered,

stepping motors can be moved in defined steps and thus positioned very precisely.

They contain 2 coils which can be powered in positive or negative

direction making the current flow in normal or reverse direction

and thus creating magnetic fields of opposite polarity

The rotor has a series of magnets (16 in case of the 28BYJ-48 which we are using)

with alternating opposite polarization.

A north pole followed by a south pole followed by a north pole and so on.

The motor base has 2*16 teeth which can be polarized as

north or south poles depending on the direction of the coil current.

Here is the data sheet of the 28BYJ-48

Slide 4: The Driver Card

The maximum current that a GPIO pin on the Raspberry Pi can deliver is 60 mA

which is insufficient to power the motor coils.

We therefore need a driver circuit (Darlington stage) to amplify

this current. In our case we use the ULN-2803 chip

The little PCB has 4 LEDs on it to show which of the 2 coils is

powered and in which direction. This is very useful to demonstrate which signals

are sent to the motor and it illustrates nicely the functioning of the motor.

Slide 5: Connecting the Driver to the Motor

We can see from the connections that when powering the pink line

the coil current is flowing in one direction while when

powering the orange line it is flowing in the opposite direction

Slide 6: Motor Movement

First we power the first coil in such a way the the first tooth has a

south pole and the second one a north pole, which

makes the rotor (whose north magnet is considered) moves to the first tooth.

Then we switch off the first coil and power the second coil such that

the first tooth of the lower row has a south pole.

This makes the rotor move to this tooth.

Now switch off the second coil and switch the first one on again,

however this time with reverse current. The second tooth of the

upper row now has the south pole

(the poles are inversed with respect to the first step).

Now we switch on only the second coil with inverse current to make

the rotor move to the forth tooth. From now on the whole cycle repeats.

Slide 7: Signal Table for Single Phase Forward

We have seen in the last slide how we have to power the coils to

make the stepping motor move by 1 cycle, which is 4 steps in case of

Single Phase Forward stepping

How does this translate into a program?

We connect the 4 phases (coil 1 forward, coil 2 backward, coil 1 backward, coil 2 forward)

to 4 GPIO pins on the Raspberry Pi cobbler

Then we create the following signal table, which is a 2-dimensional array of booleans:

Slide 8: Other modes of operation

Single Step forward (and backward) works fine but we can do better.

Up to now we have always powered only one coil at a time.

It is however possible to power both coils at the same time.

This will draw of course more current but the motor will get

a higher torque and can therefore handle bigger loads.

Slide 9: Movement Double Phase Forward

Slide 10: Double Step Forward Table

Of course our signal table must change correspondingly,

our program to send out the signals for one full cycle stays the same however.

Slide 11: Programming double step forward mode

For this, nothing much is to be said:

We change the table, but since the program is independent

from the contents of the stepping table, the code stays strictly the same

Slide 12: Position of rotor in doubleStepForward mode

An important point to note is that the rotor moves half a step

further than in single Step Forward because its north pole

is now attracted by the top and the bottom south poles.

By first powering only the upper coil, then powering both coils

then powering again only one pole of the lower coil it should

be possible to move the motor by half steps only

and by doing so increase its resolution.

This is what we call half step mode and it is a combination

of single and double step forward modes.

The torque of the motor is less than in double step forward

and the speed is only about half because now we need 8 steps for a full cycle.

Slide 13: Movement Half Step Forward

Slide 14: Half Step Forward Table

Slide 15: Programming Half Step Mode

Again, apart from the fact that we must now pass through

a table of 8 entries instead of 4 the program does not change.

If we use the signature of all bits being zero

as end of table indicator then no change at all is required.

Slide 16: The pigpio library

Up to now we always used wiringPi to access our GPIO pins.

I explained in the first lecture on the Raspberry Pi

that there are 2 independent libraries available:

• wiringPi
• wigpio

Slide 17: Advantages of pigpio

The pigpio library comes in 2 versions:

• The standard one where calls to the library code
  results in direct access to the hardware
• The daemon version where first a daemon (pigpiod)
  is started and then the hardware access is only made in this daemon

Slide 18: Accessing the daemon

The daamon is started once before we make any hardware access:

sudo pigpiod

After this all hardware access can be make by a normal user

The program communicates with the deamon through library calls

which connect to the daemon through

• pipes (when running on the Raspberry Pi) or
  
  
• through sockets when running on a remote system
  like our Ubuntu PC

We can write C programs on the PC with hardware access

to our devices on the bread board through pigpio calls to the

PC version of the library which communicates

with the pigpio daemon on the Raspberry Pi

Slide 19: Documentation of pigpio

The WEB page of pigpio can be found here

Slide 20: Features of pigpio

Slide 21: This is how to use the library

Please convert this to what will be required in your source code.

Slide 22: Sending the pulses to the hardware

Now all we have to do is to go through this table and, for each step,

send a high level to the GPIO pin to which we connected the coils.

Slide 23: Going through one step cycle

Lecture 9

Uli Raich

UCC semester 2017/2018

Signal Table for Single Phase Forward

We have seen in the last slide how we have to power the coils to

make the stepping motor move by 1 cycle, which is 4 steps in case of

Single Phase Forward stepping

How does this translate into a program?

We connect the 4 phases (coil 1 forward, coil 2 backward, coil 1 backward, coil 2 forward)

to 4 GPIO pins on the Raspberry Pi cobbler

Then we create the following signal table, which is a 2-dimensional array of booleans:

Sending the pulses to the hardware

Now all we have to do is to go through this table and, for each step,

send a high level to the GPIO pin to which we connected the coils.

Going through one step cycle

Other modes of operation

Single Step forward (and backward) works fine but we can do better.

Up to now we have always powered only one coil at a time.

It is however possible to power both coils at the same time.

This will draw of course more current but the motor will get

a higher torque and can therefore handle bigger loads.

Position of rotor in doubleStepForward mode

An important point to note is that the rotor moves half a step

further than in single StepForward because its north pole

is now attracted by the top and the bottom south poles.

By first powering only the upper coil, then powering both coils

then powering again only one pole of the lower coil it should

be possible to move the motor by half steps only

and by doing so increase its resolution.

This is what we call half step mode and it is a combination

of single and double step forward modes.

The torque of the motor is less than in double step forward

and the speed is only about half because now we need 8 steps for a full cycle.

Slide 1: Stepping Motors

Lecture 8

Uli Raich

UCC semester 2017/2018

Slide 2: The 27BJY-48 stepper motor an its ULN-2803 driver module

Slide 3: Stepping Motors versus DC Motors

While DC motors simply spin when they are powered,

stepping motors can be moved in defined steps and thus positioned very precisely.

They contain 2 coils which can be powered in positive or negative

direction making the current flow in normal or reverse direction

and thus creating magnetic fields of opposite polarity

The rotor has a series of magnets (16 in case of the 28BYJ-48 which we are using)

with alternating opposite polarization.

A north pole followed by a south pole followed by a north pole and so on.

The motor base has 2*16 teeth which can be polarized as

north or south poles depending on the direction of the coil current.

Here is the data sheet of the 28BYJ-48

Slide 4: The Driver Card

The maximum current that a GPIO pin on the Raspberry Pi can deliver is 60 mA

which is insufficient to power the motor coils.

We therefore need a driver circuit (Darlington stage) to amplify

this current. In our case we use the ULN-2803 chip

The little PCB has 4 LEDs on it to show which of the 2 coils is

powered and in which direction. This is very useful to demonstrate which signals

are sent to the motor and it illustrates nicely the functioning of the motor.

Slide 5: Connecting the Driver to the Motor

We can see from the connections that when powering the pink line

the coil current is flowing in one direction while when

powering the orange line it is flowing in the opposite direction

Slide 6: Motor Movement

First we power the first coil in such a way the the first tooth has a

south pole and the second one a north pole, which

makes the rotor (whose north magnet is considered) moves to the first tooth.

Then we switch off the first coil and power the second coil such that

the first tooth of the lower row has a south pole.

This makes the rotor move to this tooth.

Now switch off the second coil and switch the first one on again,

however this time with reverse current. The second tooth of the

upper row now has the south pole

(the poles are inversed with respect to the first step).

Now we switch on only the second coil with inverse current to make

the rotor move to the forth tooth. From now on the whole cycle repeats.

-- Uli Raich - 2017-10-16

Comments

<--/commentPlugin-->