IoTWithAtmelAVRArduino < AFNOG

Tags: view all tags

---+ Using the Atmel AVR Arduino as !IoT node
---++ Introduction

Together with the Raspberry Pi the Arduino is one of the most popular platform in embedded systems. The family of Arduino boards is quite large with the Nano, Uno and Mega being the most used ones. The boards are very cheap (&lt;2 US$ for a Nano, &lt;3 US$ for the Uno and 7-8 US$ for a Mega. These were the cheapest prices I found in China)

The Arduino Uno and the Arduino Mega come with a standardized pin-out for which several piggy back "shields" are available that can simply be stacked on the processor board.
| <img alt="nano.png" height="206" src="%ATTACHURL%/nano.png" title="nano.png" width="502" /> | <img alt="uno.png" height="306" src="%ATTACHURL%/uno.png" title="uno.png" width="441" /> |
| Arduino Nano | Arduino Uno |
| <img alt="mega.png" height="388" src="%ATTACHURL%/mega.png" title="mega.png" width="507" /> |
| Arduino Mega |
The Arduino features an <b>S</b>oftware<b> D</b>evelopment <b>K</b>it, the [[https://www.arduino.cc/en/Main/Software][Arduino SDK]] or Arduino IDE (<b>I</b>ntegrated <b>D</b>evelopment <b>E</b>nvironment), which makes software development in a C++ like language as well as flashing the binary very easy. A particular advantage of the Arduino is the large number of libraries. For almost every sensor or actuator on the market you will find a library easing considerably the development of !IoT software. Libraries for network access, MQTT and Cayenne are also available.

Another advantage is the built-in 10 bit ADC making it easy to read put analog signal levels.

<img alt="arduinoSDK.png" height="873" src="%ATTACHURL%/arduinoSDK.png" title="arduinoSDK.png" width="801" />

Problems when using the AVR Arduino are the missing network interface which must be added as a shield and, at least for the Nano and the Uno, its very limited resources in RAM space (2 kBytes only).
---++ The network interface

When trying to use the Arduino as an !IoT node on Cayenne for the first time, I used the Arduino Ethernet shield as network interface. This worked without problems and the code generated in Cayenne worked out of the box. However, when trying to use the board during a workshop in a hotel there is a fair chance that only !WiFi will be available for network access.

<img alt="ethernetShield.png" height="353" src="%ATTACHURL%/ethernetShield.png" title="ethernetShield.png" width="474" />

I therefore looked for a !WiFi interface for the Arduino and found these two:
| <img alt="esp01.png" height="183" src="%ATTACHURL%/esp01.png" title="esp01.png" width="471" /> | <img alt="wifishield.png" src="%ATTACHURL%/wifishield.png" title="wifishield.png" /> |
In my collection of Arduino shields I have a multi-function board with
   * 3 user push button switches
   * 4 user LEDs
   * a 4 digit 7-segment display
   * a passive buzzer
   * a potentiometer connected to the Arduino ADC
and you can optionally connect
   * an LM35 analog temperature sensor
   * a !DS18B20 digital temperature sensor
<img alt="multifunction.png" src="%ATTACHURL%/multifunction.png" title="multifunction.png" />

I therefore decided to try getting this board connected on an Arduino Mega acting as an !IoT node and communicating through Cayenne.

*A warning: If you are not willing to put a major effort into getting the !WiFi shield to work then do not buy it!*
---++ The !WiFi interface

Both !WiFi modules are based on the ESP8266 processor chip which has a !WiFi interface integrated into its silicon and which communicates with its host processor through AT commands over a serial line. Many versions of the AT firmware are floating around on the net but you can probably do with the version pre-installed. A list of available AT commands can be found [[http://www.pridopia.co.uk/pi-doc/ESP8266ATCommandsSet.pdf][here]].

The Arduino Uno or Mega are running on 5V while the !WiFi module needs 3.3V, which means that we need a level converter. This is accomplished with the blue module seen on the left on the photo together with the ESP01. On the !WiFi shield the level converter is implemented on the board. There are also several versions of the !WiFi shield available on the market having different misspellings on them. On the one I bought the word "More" is misspelled to "Moer" and this series has wrong transistors installed on their level converters which must be replaced to make the converter work. Here is a [[https://www.instructables.com/id/ESP8266-ESP-12E-UART-Wireless-WIFI-Shield-TTL-Conv/][ detailed description]].

Another problem with the !WiFi is the fact that the communication between the CPU card and the shield uses Tx0 and Rx0, which are also used upload and flashing and for the debug monitor. In order to upload code to the Arduino flash the connection to the !WiFi shield must therefore be cut. This is done with the 2 left most switches on the 4 dip switch block (switch set to off position). Unfortunately you do not have access to these switches if the multi-function board is plugged on top of the !WiFi shield.

I therefore used the ESP01 with its level converter connected to Tx0 and Rx0 and powered with a separate 3.3V power supply. When flashing new code I have to switch this power supply off and therefore disable the ESP01. The power is switched back on once flashing has finished.
---++ The C++ code connecting the multi-function board to Cayenne

The code controlling the devices on the multi-function board as well as the programs making the devices visible on Cayenne can be found on

https://github.com/uraich/multifunctionCayenne

-- %USERSIG{UliRaich - 2019-05-10}%

---++ Comments

%COMMENT%

Attachments

Topic attachments
I	Attachment	History	Action	Size	Date	Who
png	arduinoSDK.png	r1	manage	79.1 K	2019-05-10 - 08:34	UliRaich
png	esp01.png	r1	manage	107.1 K	2019-05-10 - 08:44	UliRaich
png	ethernetShield.png	r1	manage	248.4 K	2019-05-10 - 08:41	UliRaich
png	mega.png	r1	manage	258.9 K	2019-05-10 - 08:27	UliRaich
png	multifunction.png	r1	manage	223.2 K	2019-05-10 - 09:27	UliRaich
png	nano.png	r1	manage	186.7 K	2019-05-10 - 08:27	UliRaich
png	uno.png	r1	manage	254.6 K	2019-05-10 - 08:27	UliRaich
png	wifishield.png	r1	manage	200.8 K	2019-05-10 - 09:31	UliRaich
png	wifishieldPhoto.png	r1	manage	888.4 K	2019-05-10 - 08:44	UliRaich

Topic revision: r4 - 2019-05-16 - UliRaich